Turret Rewind Slitter

410 rewind

Turret slitter specification:
Unwind type:                                Shaft-less pick-up from floor
Maximum roll diameter:              1000mm
Maximum roll width:                    1600mm
Minimum roll width:                     500mm
Maximum roll weight:                  1000Kg
Core size:                                      76mm (3”)  + 152mm (6”)
Core holding:                                Dual size mechanical chuck
Brake:                                            2 x 110 Nm Electro-magnetic type
Tension range:                             3 – 40Kg
Tension control:                          Automatic dancer arm
Static elimination:                       1 x single bar
Splice table:                                 2 x pneumatic clamps with vacuum
Guiding system:                          Actuator guiding travel +/- 50mm
End of roll detector:                    Ultrasonic sensor
Overhead web path:                    Leading to Rewind section.
Rewind section:                           Duplex dual turret centre wind
In feed to main drive:                  Specially cut rubber spreader roller
Main drive:                                   Dual driven 150mm diameter rollers with pneumatically controlled rubber nip
Main drive motor:                        5.5Kw AC Servo motor with Ether-Cat
Maximum machine speed:         600 mtr/min
In feed to slitting section:          Specially cut rubber spreader roller
Slitting type:                                Razor in air/ Rotary shear slitting
Female knife shaft:                     60mm diameter hard chromed driven shaft to fit either a grooved sleeve or female rotary shear knives
Knife positioning:                      Set via operator screen (optional)
Minimum slit width:                   40mm
Trim Removal:                            2 x oscillating trim winders
Maximum rewind diameter:      410mm & 610mm
Rewind shafts:                           4 x differential slip shafts (2 per turret)
Rewind motors:                         2 x 5.5Kw AC Servo motors with Ether-Cat network for winding & 1 x 1Kw tail wind up motor with 10:1 ratio gearbox
Lay-on assemblies:                 1650mm wide lay-on assembly with 2 rollers, the front roller is covered in 40-shore rubber. An automatic cut off cylinder is mounted to this assembly
Static elimination:                    2 x single bars
Laser core positioning:           Motorized automatic core positioner
Rollers:                                     All rollers in the rewind section are diamond cut rubber covered
Finished roll push-off:             Ball-screw controlled push off (optional)
Finished roll un-loading:         2 systems available (optional)

 

TURRET REWIND SLITTER 810

800 Turret with Off-loading & Oscillating trim winders

Turret slitter specification:
Unwind type:                                Shaft-less pick-up from floor
Maximum roll diameter:              1000mm
Maximum roll width:                    1600mm
Minimum roll width:                     500mm
Maximum roll weight:                  1000Kg
Core size:                                      76mm (3”)  + 152mm (6”)
Core holding:                                Dual size mechanical chuck
Brake:                                            2 x 110 Nm electro-magnetic type
Tension control:                           Automatic dancer arm
Static elimination:                       1 x single bar
Splice table:                                 2 x pneumatic clamps with vacuum
Guiding system:                          Actuator guiding travel +/- 50mm
End of roll detector:                    Ultrasonic sensor
Overhead web path:                    Leading to Rewind section.
Rewind section:                           Duplex dual turret centre wind
In feed to main drive:                  Specially cut rubber spreader roller
Main drive:                                   Dual driven 150mm diameter rollers with pneumatically controlled rubber nip
Main drive motor:                        AC Servo motor with Ether-Cat
Maximum machine speed:          600 mtr/min
In feed to slitting section:           Specially cut rubber spreader roller
Slitting type:                                 Razor in air/ Rotary shear slitting
Female knife shaft:                      60mm diameter hard chromed driven shaft to fit either a grooved sleeve or female rotary shear knives
Knife positioning:                        Set via operator screen (optional)
Minimum slit width:                     40mm
Trim Removal:                              2 x oscillating trim winders
Maximum rewind diameter:        810mm
Rewind shafts:                             4 x differential slip shafts (2 per turret)
Rewind motors:                           2 x AC Servo motors with Ether-Cat network for winding & 1 x 1Kw tail wind up motor with 10:1 ratio gearbox
Lay-on assemblies:                    1650mm wide lay-on assembly with 2 rollers, the front roller is covered in 40-shore rubber. An automatic cut off cylinder is mounted to this assembly
Static elimination:                       2 x single bars
Laser core positioning:              Motorized automatic core positioning
Rollers:                                         All rollers in the rewind section are diamond cut rubber covered
Finished roll push-off:                Ball-screw controlled (optional)
Finished roll off-loading:            2 systems available (optional)